HOW SHOULD I CLEAN MY WINDOWS AFTER FILM IS APPLIED?
Windows with film applied are easily cleaned without damage to their appearance as long as a few common-sense guidelines are followed:
Use a soft clean cloth, soft paper towel, or clean synthetic sponge.
Use a soft cloth or squeegee for drying the window.
Use any normal glass cleaning solution which contains no abrasive materials.
The availability of scratch resistant coatings as a standard feature of quality films has virtually eliminated the need for extra special precautions in cleaning.
WILL WINDOW FILMS CAUSE GLASS TO BREAK?
Glass breaks when stressed. There are five types of stress which may cause glass breakage:
Thermal Stress–from absorption of solar radiation.
Tensile Stress–from the weight of the glass itself.
Mechanical Flexing Stress–from wind.
Impact Stress–from flying objects, hail, baseballs.
Twisting Stress–from building or window frame sagging or settling.
The first type, thermal stress, is the only one which film may affect. The use of window films will increase the thermal stress on sunlit glass. However, there are also other factors which will increase thermal stress such as: partial shading of windows from overhangs, tightly fitting drapes or blinds, signs or decals on windows, heating and cooling vents directed at glass. In addition, different types of glass (annealed versus tempered, clear versus tinted) have different solar absorption rates and will withstand different degrees of thermal stress.
The window film manufacturers have recommended film-to-glass tables for use by factory-trained dealer installers. If a consumer is ever in doubt, he/she should request a copy of such guidelines. Listed are some glass types or conditions where the use of a solar control (not clear safety) type of window film is not recommended without extreme caution.
SINGLE PANE GLASS LARGER THAN 100 SQUARE FEET.
DOUBLE PANE GLASS LARGER THAN 40 SQUARE FEET.
CLEAR GLASS THICKER THAN 3/8 INCH.
TINTED GLASS THICKER THAN 1/4 INCH.
WINDOW FRAMING SYSTEMS OF CONCRETE, SOLID ALUMINUM, OR SOLID STEEL.
GLASS WHERE SEALANT OR GLAZING COMPOUND HAS HARDENED.
VISIBLY CHIPPED, CRACKED OR OTHERWISE DAMAGED GLASS.
REFLECTIVE, WIRED, TEXTURED, OR PATTERNED GLASS.
TRIPLE PANE GLASS.
LAMINATED GLASS WINDOWS.
WILL WINDOW FILM KILL MY HOUSE PLANTS?
In most cases if a house plant is already receiving adequate light the use of window film will not harm it. New growth or flowering may be retarded, and, for a few days, a plant may go into a state of shock while it adjusts to the light change. If a particular plant normally wilts by the end of a sunny day, it will actually thrive better with film installed. Although there are some obvious guidelines in determining what, if any, effect window film will have on a plant (for instance, dark green plants need less light than lighter colored ones), there is one sample test which can be done prior to film installation: merely move the plant to an area with less sunlight for a few days. In addition, most nurseries or local agriculture agencies can advise you whether a particular plant needs closer to maximal or minimal light.
CAN WINDOW FILM BE USED ON LOW E WINDOWS?
Whether window film should be used on low E windows and how much you will benefit depends on three factors:
Type of low E surface used on glass.
Location of low E surface in the window system.
The desired amount of heat gain reduction, heat loss reduction, or other film benefits.
There are two basic types of low E surfaces on glass. One of these is a conductive coating put on glass as it is being made. It gives some heat loss reduction, but does little to reduce heat gain into a building. The second type is a more complex system of multiple layers of metals and conductive coatings deposited on glass after it has been made. This type of low E glass gives heat reductions of 30% to 50% in addition to reducing heat loss. Obviously there will be more heat gain reduction using film on the first type. If there is any question about the type you may have, ask your glass company or the window manufacturer to send you the specific information about your glass.
The location of the low E surface in your window system is also very important in deciding whether film should be used. If the low E coating is on the room-side surface of the innermost pane of glass, the use of window film may reduce or eliminate the heat loss reduction of the glass itself. This may be more than offset by the heat gain reduction/heat loss reduction properties of the films to be used. Most low E window systems, however, consist of double pane windows where the low E surface faces the air space between the panes. In this case, film can be installed without eliminating the heat loss reduction benefit of the low E glass. The type of window film you choose for low E glass depends entirely on your desired benefit -whether you want to reduce heat gain, control glare, prevent heat loss, reduce fading or enhance the safety of your windows and glass doors. Carefully consider all these benefits before making a final decision.